彩绘膜系列
LED彩光系列
透光膜系列
3D造型系列服务导航
Product categories
您当前位置：首页>工程动态工程动态
天花吊顶安装手册
发表时间：2017-01-20 11:35:25 发表作者：phpcms 浏览次数：
软膜天花安装技巧
Soft film ceiling installation techniques
1、在安装龙骨的时候，45度角尽可能的切准；龙骨不够长，要拼接时，龙骨要切平，不要有起拱。
1, in the installation of the keel, the 45 degree angle as far as possible the cutting; keel is not long enough to be spliced, keel to be flat, do not have arch.
2、安装之前，要检查清楚软膜天花有没有脏，那一面脏，清理干净，这个还有很多人忽略的，然而软膜天花吊顶安装好了，才发现的话，不是要重新戏法拆装嘛！
2, before installation, should check whether the soft film ceiling not dirty, it is dirty, clean it, there are a lot of people overlook, however piamater ceiling ceiling installation good, only to find it, not to trick you disassembly!
3、到安装软膜天花了，先要洗干净手，然后安装，软膜天花不要掉到地下，这样会搞脏软膜，还有可能搞烂软膜天花。
3, to the installation of soft film smallpox, to wash their hands, then install, soft film smallpox don't fall into the underground, it will get dirty and may mess up the soft, soft film smallpox.
4、安装软膜天花时，龙骨的拼接的地方，要用辍平圆滑龙骨的尖角位置，再用纸胶布包一下，以免刺穿软膜。
4, the installation of soft film smallpox, the keel of the splicing place, with sharp keel flat smooth stop position, and then glue cloth, so as not to pierce the mask.
5、安装前要，准备清洁剂，准备胶水，以免修复清洁要用。上海软膜天花吊顶
5, before installation, to prepare cleaning agent, prepare glue, so as to avoid the use of clean. Shanghai piamater ceiling
软膜天花的安装细节：
Soft film ceiling installation details:
1、工地现场是否有条件安装龙骨：现场墙身是否完成，木工部分加工是否合格，需要抹灰部分先完成。灯、风口等开孔尺寸要提前加工好。
1, site installation site: whether the conditional keel wall is completed, woodworking processing part is qualified, need to complete part of plastering. Lamps, air vents and other openings to be processed in advance.
2、首先要按图纸设计要求的木工做好部分进行固定铝合金龙骨龙骨，注意角位一定要直角平整光滑，驳接要平、密。
2, first of all, according to the design requirements of the carpenter to do a good part of the fixed aluminum alloy keel, pay attention to the corner must be smooth and smooth, and then to be flat.
3、注意灯架、风口、光管盘要与周边的龙骨水平，并且要求牢固平稳不能摇摆方可。
3, pay attention to the lamp holder, tuyere, light tube plate and the keel of the surrounding level, and the requirements of a firm and stable can not swing.
4、烟感、吸顶灯，先定位再做一个木底架，木底架底面要打磨光滑，并注意水平高度，太低就容易凸现底架的痕迹。
4, smoke, ceiling lamps, the first position to make a wooden frame wooden chassis underside to polish, and pay attention to the level of height is too low, it is easy to show a trace.
5、安装天花之前，认真检查龙骨接头是否牢固和光滑，喷淋头要粘上白胶带，风口要处理好。安装天花时要先从中间往两边固定，同时注意两边尺寸，注意焊接缝要直最后做角位,注意要平整光滑。四周做好后把多出的天花修剪去除。达到完美的收边效果。
5, before the installation of smallpox, carefully check whether the keel joint is firm and smooth, spray head to stick on white tape, tuyere to handle. Installation of smallpox from the middle to both sides of the first fixed, while the attention of both sides of the size, pay attention to the last straight seam welding angle, pay attention to smooth. After more than four months to do more than the removal of smallpox pruning. To achieve the perfect edge effect.
6、开灯孔：在灯孔的位置上做好记号，把PVC灯圈小心准确地粘在软膜的底面，待牢固后把多出的天花去除即可。
6, turn on the lights in the lamp hole hole: make a mark on the position of the PVC lamp ring carefully accurately glued to the bottom surface of film, to be strong after the removal of smallpox can be.
7、.开风口、光管盘口：找到风口光管盘口的位置，跟做四周一样，把软膜安装到铝合金龙骨上，注意角位要平整。做好后把多出的天花切除即可。
7. Open the tuyere, the light pipe handicap: find the outlet tube position position, like around the soft film mounted to Aluminum Alloy keel, note the angle should be smooth. After the completion of the smallpox can be removed.
8、最后用干净毛巾清洁软膜天花表面。
At the end of 8, with a clean towel to clean the surface of soft film smallpox.
以上这些如果能做到的话，做起事情来就顺手很多了。
If these can be done, do things on a lot easier.
Soft film ceiling installation techniques
1、在安装龙骨的时候，45度角尽可能的切准；龙骨不够长，要拼接时，龙骨要切平，不要有起拱。
1, in the installation of the keel, the 45 degree angle as far as possible the cutting; keel is not long enough to be spliced, keel to be flat, do not have arch.
2、安装之前，要检查清楚软膜天花有没有脏，那一面脏，清理干净，这个还有很多人忽略的，然而软膜天花吊顶安装好了，才发现的话，不是要重新戏法拆装嘛！
2, before installation, should check whether the soft film ceiling not dirty, it is dirty, clean it, there are a lot of people overlook, however piamater ceiling ceiling installation good, only to find it, not to trick you disassembly!
3、到安装软膜天花了，先要洗干净手，然后安装，软膜天花不要掉到地下，这样会搞脏软膜，还有可能搞烂软膜天花。
3, to the installation of soft film smallpox, to wash their hands, then install, soft film smallpox don't fall into the underground, it will get dirty and may mess up the soft, soft film smallpox.
4、安装软膜天花时，龙骨的拼接的地方，要用辍平圆滑龙骨的尖角位置，再用纸胶布包一下，以免刺穿软膜。
4, the installation of soft film smallpox, the keel of the splicing place, with sharp keel flat smooth stop position, and then glue cloth, so as not to pierce the mask.
5、安装前要，准备清洁剂，准备胶水，以免修复清洁要用。上海软膜天花吊顶
5, before installation, to prepare cleaning agent, prepare glue, so as to avoid the use of clean. Shanghai piamater ceiling
软膜天花的安装细节：
Soft film ceiling installation details:
1、工地现场是否有条件安装龙骨：现场墙身是否完成，木工部分加工是否合格，需要抹灰部分先完成。灯、风口等开孔尺寸要提前加工好。
1, site installation site: whether the conditional keel wall is completed, woodworking processing part is qualified, need to complete part of plastering. Lamps, air vents and other openings to be processed in advance.
2、首先要按图纸设计要求的木工做好部分进行固定铝合金龙骨龙骨，注意角位一定要直角平整光滑，驳接要平、密。
2, first of all, according to the design requirements of the carpenter to do a good part of the fixed aluminum alloy keel, pay attention to the corner must be smooth and smooth, and then to be flat.
3、注意灯架、风口、光管盘要与周边的龙骨水平，并且要求牢固平稳不能摇摆方可。
3, pay attention to the lamp holder, tuyere, light tube plate and the keel of the surrounding level, and the requirements of a firm and stable can not swing.
4、烟感、吸顶灯，先定位再做一个木底架，木底架底面要打磨光滑，并注意水平高度，太低就容易凸现底架的痕迹。
4, smoke, ceiling lamps, the first position to make a wooden frame wooden chassis underside to polish, and pay attention to the level of height is too low, it is easy to show a trace.
5、安装天花之前，认真检查龙骨接头是否牢固和光滑，喷淋头要粘上白胶带，风口要处理好。安装天花时要先从中间往两边固定，同时注意两边尺寸，注意焊接缝要直最后做角位,注意要平整光滑。四周做好后把多出的天花修剪去除。达到完美的收边效果。
5, before the installation of smallpox, carefully check whether the keel joint is firm and smooth, spray head to stick on white tape, tuyere to handle. Installation of smallpox from the middle to both sides of the first fixed, while the attention of both sides of the size, pay attention to the last straight seam welding angle, pay attention to smooth. After more than four months to do more than the removal of smallpox pruning. To achieve the perfect edge effect.
6、开灯孔：在灯孔的位置上做好记号，把PVC灯圈小心准确地粘在软膜的底面，待牢固后把多出的天花去除即可。
6, turn on the lights in the lamp hole hole: make a mark on the position of the PVC lamp ring carefully accurately glued to the bottom surface of film, to be strong after the removal of smallpox can be.
7、.开风口、光管盘口：找到风口光管盘口的位置，跟做四周一样，把软膜安装到铝合金龙骨上，注意角位要平整。做好后把多出的天花切除即可。
7. Open the tuyere, the light pipe handicap: find the outlet tube position position, like around the soft film mounted to Aluminum Alloy keel, note the angle should be smooth. After the completion of the smallpox can be removed.
8、最后用干净毛巾清洁软膜天花表面。
At the end of 8, with a clean towel to clean the surface of soft film smallpox.
以上这些如果能做到的话，做起事情来就顺手很多了。
If these can be done, do things on a lot easier.